STUDIO-QUALITY ELECTRET MIC PREAMP BUILD: SOUND LIKE A STUDIO MIC GUARANTEED!
Welcome, buddies! In today’s article, we’re going to build a studio-quality electret mic pre-amplifier that sounds awesome, it’ll rival professional studio microphones!
What?? I know what you’re thinking: Building a mic preamp with a cheap ECM instead of an expensive condenser mic? " Aren’t there already tons of videos and diagrams showing how to build one?"
Yes, it’s true preamp circuits are all over the internet But here’s the catch: most of them don’t deliver the professional-quality sound you’re hoping for. Even if the circuit works, the audio quality often includes excessive noise, distortion, or an unnatural tone.
In my opinion, the problem isn’t the mic; it’s the design of the preamp circuit. Even a generic ECM mic that costs around 20 cents can sound great if the circuit is properly designed and optimized for it. That’s exactly what we’re going to do in this video: design a circuit that pushes the limits of what a cheap electret mic can do!
The reason most preamp circuits don’t meet expectations is that designing a good preamp isn’t as simple as throwing a few components together. It requires careful attention to detail and a deep understanding of analog electronics.
These are only a few of them. There are a lot of steps that remain in designing a fully featured preamp. So I decided to create a specific datasheet that includes step- by-step calculations and contains the appropriate formulas. I am currently working on it.
For this project, I’ve chosen a non-inverting op-amp configuration for the preamp. This configuration is ideal for amplifying low-level signals from a microphone while maintaining stability and low noise.
The circuit also includes built-in high-pass and low-pass filters, which are essential for shaping the audio signal:
This circuit is designed to be operated at 5v (Use battery supply as possible that reduces the power noise that overall reduces the noise of the preamp)
Note: Use low tolerance resistor and COG or tantalum capacitors as possible for this design.
As for the mic, I used a generic CZN-15E electret mic. It’s cheap, easy to find, and gets the job done. If you want to upgrade, pick any mic with these specs:
These parameters are usually specified in a microphone datasheet.
Before building the circuit, I simulated it in LTspice to verify its performance. Simulations help catch potential issues before building the actual hardware.
In the simulation result, our preamp outputs 454mV (amplitude) or 321mV (RMS), which is a line-level signal that we expect from an input voltage of around 29.343mv calculated using mic sensitivity -32 (Wait, I am working on designing a complete datasheet that include all the calculation including this one.)
Of course, no preamp build is complete without a real-world test. I’ll connect the preamp to the electret mic and record audio samples with a distance of 50cm from mic to audio source. This will give you a clear idea of how the circuit performs and what kind of audio quality you can expect.
Here’s a quick but important note: do NOT connect the output of this preamp to your PC’s mic input. Instead, connect it to the line-in port. This setup ensures you get the best sound quality without distortion or noise.
To connect the preamp’s output to a device like your PC or recorder, you’ll need a 3.5mm TRS cable. Since our circuit is mono, we’ll only use the Tip and Sleeve connections, while the Ring will remain unconnected. Here’s how it works:
Using a TRS cable ensures compatibility with standard audio devices, like the line-in port on a PC or an external recorder. Plus, it provides a clean and professional connection for your project.
For this project, I’m using the NE5532P op-amp, but I recommend the LM833 for its excellent audio performance, including high slew rate, wide gain-bandwidth product, and low noise.
Click the link below to download the schematic diagram of the electret mic preamplifier as a PDF, later i will also add a datasheet:
Download Schematics PDFMB-727 Studio Electret Pre-amp by Mubarak Basha is licensed
under CC BY-SA 4.0
This project proves you don’t need expensive microphones or equipment to achieve great audio quality. With the right design, even a budget electret mic can deliver studio-level performance.
If you’re passionate about audio and love DIY projects, give this a try! Share your results or ask questions in the contact page of my website—I’d love to hear from you. If you found this article helpful and would like to support my work, consider supporting my work through sharing with your hobbyist friends and family member. Your contributions help me continue creating exciting electronics projects and sharing knowledge with the community. For feedback or improvement contact me with a Project name of MB-727 Preamp.